New pages
18 August 2026
- 02:4902:49, 18 August 2026 Lua (hist | edit) [17,269 bytes] Joesphan (talk | contribs) (Created page with "safsefwefewfewfwef") Tag: Visual edit
11 June 2026
- 15:1115:11, 11 June 2026 Error Codes (hist | edit) [16,665 bytes] ZeeKay (talk | contribs) (Created page with "Epic EFI has custom error codes similar to OBD2. == Code 6000 - CUSTOM_NAN_ENGINE_LOAD == == Code 6001 - CUSTOM_WRONG_ALGORITHM == == Code 6002 - CUSTOM_NAN_ENGINE_LOAD_2 == == Code 6003 - CUSTOM_OBD_6003_FLEX_FUEL_TEMP_LOW == == Code 6004 - CUSTOM_OBD_6004_FLEX_FUEL_TEMP_HIGH == == Code 6005 - CUSTOM_6005 == == Code 6006 - CUSTOM_6006 == == Code 6007 - CUSTOM_6007 == == Code 6008 - CUSTOM_6008 == == Code 6009 - CUSTOM_6009 == == Code 6010 - CUSTOM_6010 == ==...") Tag: Visual edit
6 June 2026
- 22:2022:20, 6 June 2026 Config:Expert Extra (hist | edit) [39,704 bytes] Ogalic (talk | contribs) (Created page with "<!-- group:EFI Expert --> = EFI Expert = <!-- section:efiExpertGeneral --> == EFI Expert General settings == <!-- field:flashWriteDelay --> ==== Delay writing flash tune ==== Delay flash write after engine stop for this long <!-- field:neverWrite --> ==== Do not automatically save settings(ECU READONLY) ==== ECU is in read only mode. use 'Write Config' in bench test to save things. <!-- field:update_prog_outputs_200hz --> ==== Update programmable outputs every 200hz...")
- 22:1922:19, 6 June 2026 Config:Controller (hist | edit) [4,086 bytes] Ogalic (talk | contribs) (Created page with "<!-- section:ecuStimulator --> = ECU stimulator = <!-- field:triggerSimulatorRpm --> ==== Trigger Simulator ==== <!-- field:stimulatorBench --> ==== Stimulator Bench extension ==== Stimulator is running bench counts and injector pulsewidths <!-- field:benchTestCount --> ==== Count ==== How many test bench pulses do you want <!-- field:benchTestOnTime --> ==== Injector Pulsewidth Override ==== Duration of each test pulse <!-- field:triggerSimulatorPins1 --> ==== trig...")
- 22:1822:18, 6 June 2026 Config:CAN Bus (hist | edit) [113,503 bytes] Ogalic (talk | contribs) (Created page with "<!-- section:canBusMain --> = CAN Bus Settings = <!-- section:canBus --> == CAN Bus == <!-- field:canNbcType --> ==== CAN dash type ==== <!-- field:imuType --> ==== Inertia Measurement Unit ==== * '''None''' * '''VAG''' * '''MM5.10''' * '''type 3''' * '''type 4''' <!-- field:canCheckedDigitalEnable --> ==== Enable canchecked.de MCE18 digital states ==== Enable CANCHECKED 0x702 digital states <!-- field:canCheckedAnalogEnable --> ==== Enable canchecked.de MCE18 analo...")
- 22:1722:17, 6 June 2026 Config:Sensors (hist | edit) [46,426 bytes] Ogalic (talk | contribs) (Created page with "<!-- section:cltSensor --> = Coolant temperature (CLT) = <!-- section:clt_thermistor --> == Coolant Temperature sensor (CLT) == <!-- field:clt_adcChannel --> ==== Input channel ==== ?highlight=class~analog_inputs * '''$adc_channel_e_list''' <!-- field:clt_bias_resistor --> ==== Pullup resistor ==== Pull-up resistor value on your board <!-- field:clt_tempC_1 --> ==== Lowest temperature ==== these values are in Celcius <!-- field:clt_resistance_1 --> ==== Resistance...")
- 22:1522:15, 6 June 2026 Config:Advanced (hist | edit) [225,978 bytes] Ogalic (talk | contribs) (Created page with "<!-- section:smLaunchControl --> = Launch Control = <!-- section:smLaunchControlWest --> == Launch Control Settings == <!-- field:launchControlEnabled --> ==== Launch Control ==== <!-- field:launchActivationMode --> ==== Activation Mode ==== * '''Launch Button''' * '''Clutch Down Switch''' * '''Speed Based''' * '''Brake Pedal''' * '''Lua''' * '''TPS based''' * '''Clutch Up''' <!-- field:clutchDownPin --> ==== Clutch Down ==== Some cars have a switch to indicate that...") Tag: Visual edit: Switched
5 June 2026
- 16:3516:35, 5 June 2026 NTC coolant temperature sensor (hist | edit) [1,016 bytes] M-Kay (talk | contribs) (→NTC coolant temperature sensors: new section)