Config:Setup - Revision history

Ogalic: Ogalic moved page Setup to Config:Setup

2026-02-01T15:50:21Z

← Older revision	Revision as of 15:50, 1 February 2026
(No difference)

Gurov: /* Rotational cut spark */

2026-01-15T10:44:28Z

Rotational cut spark

← Older revision		Revision as of 10:44, 15 January 2026
Line 75:		Line 75:

	==== Rotational cut spark ====		==== Rotational cut spark ====
	~~@ggurov?~~		Rotational REV LIMIT will cut spark, using the rotational pattern proportional to location of current rpm in HARD LIMIT - ROTATIONAL WINDOW. If Both this and below is false, spark is cut, if this is true and below is false, spark is also cut.

	==== Rotational cut fuel ====		==== Rotational cut fuel ====
	~~@ggurov?~~		Rotational REV LIMIT will cut fuel, on the same pattern If this both this and above are false, spark is cut, if this is true, and above is false, fuel is cut.

	==== Rotational Rev Limit absolute ignition ====		==== Rotational Rev Limit absolute ignition ====

Ogalic at 10:39, 15 January 2026

2026-01-15T10:39:10Z

← Older revision		Revision as of 10:39, 15 January 2026
Line 1:		Line 1:
			[[File:Setup menu.png\|thumb\|Setup menu]]
	This is the first setup menu in TunerStudio.		This is the first setup menu in TunerStudio.

Ogalic at 10:32, 15 January 2026

2026-01-15T10:32:57Z

@@ Line 1: / Line 1: @@
 = Vehicle Information =
 This is used for basic engine and car information.
@@ Line 741: / Line 743: @@
 ==== A/C pressure enable hysteresis(kPa) ====
 If [[Setup#Pressure High disable(kPa)|Pressure High Disable(kPa)]] is 240kpa, and the hystheresis is 20 kPa, when the ECU sees 240kpa the A/C will be disabled and stay disabled until 240 - 20 = 220 kPa is reached.

Ogalic: /* Air Conditioning */

2026-01-15T09:24:38Z

Air Conditioning

← Older revision		Revision as of 09:24, 15 January 2026
Line 740:		Line 740:

	==== A/C pressure enable hysteresis(kPa) ====		==== A/C pressure enable hysteresis(kPa) ====
	If Pressure High Disable is 240kpa, and ~~acPressureEnableHyst~~ is 20, when the ECU sees 240kpa, A/C will be disabled, and stay disabled until 240-20=~~220kpa~~ is reached		If [[Setup#Pressure High disable(kPa)\|Pressure High Disable(kPa)]] is 240kpa, and the hystheresis is 20 kPa, when the ECU sees 240kpa the A/C will be disabled and stay disabled until 240 - 20 = 220 kPa is reached.

Ogalic: /* Tach Correction Curve */

2026-01-15T09:22:01Z

Tach Correction Curve

@@ Line 681: / Line 681: @@
 = Tach Correction Curve =
-This is the tachometer correction curve. See [[Setup#Tachometer output|Tachometer output.]]
+This is the tachometer correction curve. The tachometer output correction multiplier is used to compensate for non-linear tachometer response.
 = Speedo Correction Curve =
-This is the speedometer correction curve. See [[Setup#Speedometer output|Speedometer output]].
+This is the speedometer correction curve. The speedometer output correction multiplier is used to to compensate for non-linear speedometer response.

Ogalic: /* Water Pump x PWM curve */

2026-01-15T09:13:22Z

Water Pump x PWM curve

← Older revision		Revision as of 09:13, 15 January 2026
Line 679:		Line 679:
	= Water Pump x PWM curve =		= Water Pump x PWM curve =
	This is the water pump controller PWM curve. To use PWM water pump control, see [[Setup#Water Pump PWM enable\|Water Pump PWM enable]].		This is the water pump controller PWM curve. To use PWM water pump control, see [[Setup#Water Pump PWM enable\|Water Pump PWM enable]].

			= Tach Correction Curve =
			This is the tachometer correction curve. See [[Setup#Tachometer output\|Tachometer output.]]

			= Speedo Correction Curve =
			This is the speedometer correction curve. See [[Setup#Speedometer output\|Speedometer output]].

Ogalic: /* Fan x PWM curve */

2026-01-15T09:10:33Z

Fan x PWM curve

← Older revision		Revision as of 09:10, 15 January 2026
Line 648:		Line 648:
	How much idle percentage will be added to the idle controller while the fan is running. In PWM mode this is scaled according to PWM %.		How much idle percentage will be added to the idle controller while the fan is running. In PWM mode this is scaled according to PWM %.

	==== PWM enable ====		==== Water Pump PWM enable ====
	This switches the controller from a on/off controller to a PWM controller.		This switches the controller from a on/off controller to a PWM controller.

Line 675:		Line 675:

	= Fan x PWM curve =		= Fan x PWM curve =
	This is the fan controller PWM curve. To use PWM fan control, see #Fan PWM ~~Enable~~.		This is the fan controller PWM curve. To use PWM fan control, see [[Setup#Fan PWM enable\|Fan PWM enable]].

			= Water Pump x PWM curve =
			This is the water pump controller PWM curve. To use PWM water pump control, see [[Setup#Water Pump PWM enable\|Water Pump PWM enable]].

Ogalic: /* Water Pump x Button Mode */

2026-01-15T09:09:12Z

Water Pump x Button Mode

← Older revision		Revision as of 09:09, 15 January 2026
Line 589:		Line 589:
	Additional idle % when fan x is active. In PWM mode this is scaled according to PWM %.		Additional idle % when fan x is active. In PWM mode this is scaled according to PWM %.

	==== PWM enable ====		==== Fan PWM enable ====
	This enables PWM control of the fan. This disables the on/off functionality, they are mutually exclusive.		This enables PWM control of the fan. This disables the on/off functionality, they are mutually exclusive.

Line 673:		Line 673:
	==== Water Pump x Button Mode ====		==== Water Pump x Button Mode ====
	See [[Hardware:ECU input mode selection\|ECU input mode selection]].		See [[Hardware:ECU input mode selection\|ECU input mode selection]].

			= Fan x PWM curve =
			This is the fan controller PWM curve. To use PWM fan control, see #Fan PWM Enable.

Ogalic: /* Check Engine Settings */

2026-01-15T09:07:42Z

Check Engine Settings

← Older revision		Revision as of 09:07, 15 January 2026
Line 552:		Line 552:
	==== Warning Period(s) ====		==== Warning Period(s) ====
	@gurov: Not really clear		@gurov: Not really clear

			== Fans and Water Pumps ==
			This enables the control of fans and water pumps. Both functionalities support PWM.

			== Fan Settings - Fan x ==

			==== Enable Fan x ====
			If the fan output is enabled for this fan.

			==== Output ====
			This is the physical output pin of the check engine light.
			See [[Hardware:ECU output mode selection\|ECU output mode selection]].

			==== Output mode ====
			See [[Hardware:ECU output mode selection\|ECU output mode selection]].

			==== On temperature(deg C) ====
			Cooling fan turn-on temperature threshold, in Celsius.

			==== Off temperature(deg C) ====
			Cooling fan turn-off temperature threshold, in Celsius.

			==== Enable with AC ====
			Turn on this fan when AC is on.

			==== Disable when engine stopped ====
			Inhibit operation of this fan while the engine is not running.

			==== After this many seconds ====
			Fan x timeout after this many seconds of engine stop.

			==== Disable above vehicle speed ====
			This is the speed after the engine fan will be disabled. Use this if the airflow above a certain speed is sufficient enough to cool the engine so the fans don't run.

			==== Idle adder(%) ====
			Additional idle % when fan x is active. In PWM mode this is scaled according to PWM %.

			==== PWM enable ====
			This enables PWM control of the fan. This disables the on/off functionality, they are mutually exclusive.

			==== PWM frequency ====
			The frequency of the PWM controller.

			==== Min PWM(%) ====
			This is the minimum PWM value of the fan controller.

			==== Max PWM(%) ====
			This is the maximum PWM value of the fan controller.

			==== AC adder(%) ====
			How much % PWM will the AC add to the fan duty.

			==== PWM soft-start(s) ====
			This is how long the PWM duty cycle slope should last to provide soft-start functionality. This limits the inrush current into the fans to prevent blowing of fuses/damaging the controllers.

			==== Fan x Button ====
			This is the manual fan override button.

			==== Fan x Button mode ====
			See [[Hardware:ECU input mode selection\|ECU input mode selection]].

			== Water Pump x ==
			This enables the control of water pumps using on/off algorithms or PWM.

			==== Enable Water Pump ====
			If this water pump should be enabled.

			==== Output ====
			This is the physical output pin of the water pump.

			To find the actual value for your hardware, see [[Hardware]].

			==== Output mode ====
			See [[Hardware:ECU output mode selection\|ECU output mode selection]].

			==== On temperature(deg C) ====
			Water pump turn-on temperature threshold, in Celsius.

			==== Off temperature(deg C) ====
			Water pump turn-off temperature threshold, in Celsius.

			==== Enable with AC ====
			Turn on the water pump when AC is on.

			==== Disable with engine stopped ====
			If the water pump should be disabled while the engine is stopped.

			==== After this many seconds ====
			Timeout of the water pump after the engine is stopped.

			==== Disable above vehicle speed ====
			@gurov: Why would one disable a water pump above vss?

			==== Idle adder(%) ====
			How much idle percentage will be added to the idle controller while the fan is running. In PWM mode this is scaled according to PWM %.

			==== PWM enable ====
			This switches the controller from a on/off controller to a PWM controller.

			==== PWM frequency ====
			This is the frequency of the PWM controller.

			==== Min PWM(%) ====
			The minimum duty cycle for the water pump output.

			==== Max PWM(%) ====
			This is the maximum duty cycle for the water pump output.

			==== AC added(%) ====
			How much duty cycle is added when the water pump is running.

			==== PWM soft-start(s) ====
			This is how long the PWM duty cycle slope should last to provide soft-start functionality. This limits the inrush current into the pumps to prevent blowing of fuses/damaging the controllers.

			==== Water Pump x Button ====
			This is the override button physical input to enable the water pump.

			To find the actual value for your hardware, see [[Hardware]].

			==== Water Pump x Button Mode ====
			See [[Hardware:ECU input mode selection\|ECU input mode selection]].