Ogalic: Created page with " = ECU stimulator = ==== Trigger Simulator ==== ==== Stimulator Bench extension ==== Stimulator is running bench counts and injector pulsewidths ==== Count ==== How many test bench pulses do you want ==== Injector Pulsewidth Override ==== Duration of each test pulse ==== trig..."

2026-06-06T22:19:31Z

Created page with " = ECU stimulator =  ==== Trigger Simulator ====  ==== Stimulator Bench extension ==== Stimulator is running bench counts and injector pulsewidths  ==== Count ==== How many test bench pulses do you want  ==== Injector Pulsewidth Override ==== Duration of each test pulse  ==== trig..."

New page

= ECU stimulator =


==== Trigger Simulator ====


==== Stimulator Bench extension ====
Stimulator is running bench counts and injector pulsewidths


==== Count ====
How many test bench pulses do you want


==== Injector Pulsewidth Override ====
Duration of each test pulse


==== trigger stimulator output #1 ====
Each rusEFI piece can provide synthetic trigger signal for external ECU. Sometimes these wires are routed back into trigger inputs of the same rusEFI board.
See also directSelfStimulation which is different. 1

* '''$gpio_list'''


==== trigger stimulator output mode #1 ====
triggerSimulatorPinModes 1

* '''$pin_output_mode_e_enum'''


==== trigger stimulator output #2 ====
Each rusEFI piece can provide synthetic trigger signal for external ECU. Sometimes these wires are routed back into trigger inputs of the same rusEFI board.
See also directSelfStimulation which is different. 2

* '''$gpio_list'''


==== trigger stimulator output mode #2 ====
triggerSimulatorPinModes 2

* '''$pin_output_mode_e_enum'''


==== camSimulatorPin ====
* '''$gpio_list'''


==== camSimulatorPinMode ====
* '''$pin_output_mode_e_enum'''


==== Engine chart size ====


= Hardware Test mode =


== Spark ==


== Injector Test ==


==== Count ====
How many test bench pulses do you want


==== On Time ====
Duration of each test pulse


==== Off Time ====
Time between bench test pulses


== Lua Out Test ==


== Misc ==


== Reference gauges ==


= epicEFI experimental tunables =


==== Calmer Burn - do not reconfigure sensors on running engine, rpm > 0 ====
do not reset sensors and all hardware when clicking burn, or closing window with engine running


==== Map Low Pass Cutoff Hz ====


==== MAF Low Pass Cutoff Hz ====


==== AUX Low Pass Cutoff Hz ====


==== PPS Low Pass Cutoff Hz ====


==== TPS Low Pass Cutoff Hz ====


==== EGO Low Pass Cutoff Hz ====


==== Low fuel pressure low pass cutoff ====


==== Disable Programmable outputs ====


==== Allow DFU With IGN voltage ====
danger zone - allow entry into DFU with 12v active - if injection/ignition is connected to usart1/usart3, their state is unpredictable in DFU


==== No tps/pps redundancy required, super dangerous ====


==== Ignore TPS/PPS sensors too close to each other ====
Ignore TPS/PPS sensors too close to each other


==== Disable MCP3208 + accelerometer ====


==== Disable epic DINP ====


==== Disable epic INJOK ====


==== Disable EGT ====


==== Disable BARO ====


==== Enable init HS to logic high ====
Iinit Epic High Side in logic high


= Digital input pullups =


==== Enable DIN1 pullup ====
Enable software pullup on DIN1 (drives PE2 high when set)


==== Enable DIN2 pullup ====
Enable software pullup on DIN2 (drives PE3 high when set)

Config:Controller - Revision history