View source for Config:Expert Extra

<!-- group:EFI Expert -->
= EFI Expert =

<!-- section:efiExpertGeneral -->
== EFI Expert General settings ==

<!-- field:flashWriteDelay -->
==== Delay writing flash tune ====
Delay flash write after engine stop for this long

<!-- field:neverWrite -->
==== Do not automatically save settings(ECU READONLY) ====
ECU is in read only mode. use 'Write Config' in bench test to save things.

<!-- field:update_prog_outputs_200hz -->
==== Update programmable outputs every 200hz ====
Update programmable outputs every 200hz

<!-- field:internalFlashSleep -->
==== Sleep half a second before writing to internal flash and before writing to backup flash on burn ====
sleep half a second before writing to internal flash and before writing to backup flash on burn

<!-- field:deferAllWritesUntilEngineOff -->
==== Defer all FLASH writes until engine off (H7) ====
Do not write while running

<!-- field:overrideUaefiVbat -->
==== Override uaefi voltage dividers ====
Allow overriding uaefi voltage dividers

<!-- field:ignore_no_etb_error -->
==== Ignore no ETB error ====
While setting up ETB, sometimes there is an error that prevents ecu from continuing calibration, use this to ignore that error

<!-- field:total_shift_no_rpm_reset -->
==== Total shift no RPM reset ====

<!-- field:gdiIgnoreSyncForIgnition -->
==== Ignore full sync requirement for ignition and GDI ====
Ignore demand for synchronization for ignition and GDI

<!-- field:skipFlashWrite -->
==== Skip flash write ====
Skip flash write.

<!-- field:allow_multiple_input_assign -->
==== Allow multiple input assignments to the same pin ====
Allow multiple input assignments to the same pin

<!-- field:fast_sensor_get -->
==== Fast sensor get, this will disable timeouts for all sensors ====
Fast sensor get, this will disable timeouts for all sensors

<!-- field:ms_can_bcast_clt_celcius -->
==== MS CAN broadcast CLT in Celsius instead of Fahrenheit ====
MS CAN broadcast CLT in Celsius instead of Fahrenheit

<!-- field:console_version_print_disabled -->
==== Disable console version print ====
Disable console version print

<!-- field:hellen_unassign_leds -->
==== Unassign Hellen LEDs ====
LEDs not assigned to any physical pin

<!-- field:luaCriticalErrorAllowEcu -->
==== Allow ECU to continue on Lua critical error ====
allow ecu to continue on lua critical error

<!-- field:disable_thermistor_checks -->
==== Disable thermistor checks ====
Disable checking 10% and 90% point validation of the thermistor configuration

<!-- field:disable_sdcard_tune -->
==== Disable SD card tune backup/restore ====
Disable SD card tune backup/restore for writing while running

<!-- section:efiExpertFuelSettings -->
== EFI Expert Fuel settings ==

<!-- field:bypassTcharge -->
==== Bypass Tcharge - use IAT instead of modeled Tcharge ====
use IAT instead of modeled Tcharge

<!-- field:disableIncorporateAFR -->
==== Disable Incorporate AFR function from SD ====
Disable incorporate afr function

<!-- field:disable_multiply_by_map -->
==== Disable multiplying by MAP for fueling ====
Disable multiplying by MAP for fueling.

<!-- field:map_for_bypass -->
==== MAP for bypassing MAP multiply calculations ====
MAP for bypassing VE calculations

<!-- field:MAFMAPLoadIsMAF -->
==== MAFMAP Load Calculations is based on MAF ====
Use MAFMAP blended engine load in load calculations, MAP is default

<!-- field:MAFMAPMAXAirmass -->
==== During Map Prediction, take the higher airmass of maf/map calculations ====
when map prediction is active, take the higher airmass of maf/map calculations

<!-- field:TMFLoadIsTMF -->
==== TMF Load Calculations is based on 100% VE cyl fill ====
Use TMF 100% ve-based engine load calculation, MAP is default

<!-- field:TMFPressureSplitPercentUp -->
==== TMF map UP margin (manifold pressure split for averaging flow) ====
averaging manifold pressure split for smoother choked airflow transition UP (%)

<!-- field:TMFPressureSplitPercentDown -->
==== TMF map DOWN margin (manifold pressure split for averaging flow) ====
averaging manifold pressure split for smoother choked airflow transition DOWN (%)

<!-- group:LUA -->
= LUA =

<!-- section:auxInputsDialog -->
== Lua Analog Inputs ==

<!-- field:auxAnalogInputs1 -->
==== ADC #1 ====
auxAnalogInputs 1
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs2 -->
==== ADC #2 ====
auxAnalogInputs 2
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs3 -->
==== ADC #3 ====
auxAnalogInputs 3
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs4 -->
==== ADC #4 ====
auxAnalogInputs 4
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs5 -->
==== ADC #5 ====
auxAnalogInputs 5
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs6 -->
==== ADC #6 ====
auxAnalogInputs 6
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs7 -->
==== ADC #7 ====
auxAnalogInputs 7
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs8 -->
==== ADC #8 ====
auxAnalogInputs 8
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- section:luaDigitalInputsDialog -->
== Lua Digital Inputs ==

<!-- field:luaDigitalInputPins1 -->
==== Digital #1 ====
luaDigitalInputPins 1
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPins2 -->
==== Digital #2 ====
luaDigitalInputPins 2
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPins3 -->
==== Digital #3 ====
luaDigitalInputPins 3
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPins4 -->
==== Digital #4 ====
luaDigitalInputPins 4
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPins5 -->
==== Digital #5 ====
luaDigitalInputPins 5
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPins6 -->
==== Digital #6 ====
luaDigitalInputPins 6
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPins7 -->
==== Digital #7 ====
luaDigitalInputPins 7
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPins8 -->
==== Digital #8 ====
luaDigitalInputPins 8
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:luaDigitalInputPinModes1 -->
==== Mode #1 ====
luaDigitalInputPinModes 1

* '''$pin_input_mode_e_enum'''

<!-- field:luaDigitalInputPinModes2 -->
==== Mode #2 ====
luaDigitalInputPinModes 2

* '''$pin_input_mode_e_enum'''

<!-- field:luaDigitalInputPinModes3 -->
==== Mode #3 ====
luaDigitalInputPinModes 3

* '''$pin_input_mode_e_enum'''

<!-- field:luaDigitalInputPinModes4 -->
==== Mode #4 ====
luaDigitalInputPinModes 4

* '''$pin_input_mode_e_enum'''

<!-- field:luaDigitalInputPinModes5 -->
==== Mode #5 ====
luaDigitalInputPinModes 5

* '''$pin_input_mode_e_enum'''

<!-- field:luaDigitalInputPinModes6 -->
==== Mode #6 ====
luaDigitalInputPinModes 6

* '''$pin_input_mode_e_enum'''

<!-- field:luaDigitalInputPinModes7 -->
==== Mode #7 ====
luaDigitalInputPinModes 7

* '''$pin_input_mode_e_enum'''

<!-- field:luaDigitalInputPinModes8 -->
==== Mode #8 ====
luaDigitalInputPinModes 8

* '''$pin_input_mode_e_enum'''

<!-- section:luaOutputs -->
== Lua Script PWM Outputs ==

<!-- field:luaOutputPins1 -->
==== output #0 ====
luaOutputPins 1
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:luaOutputPins2 -->
==== output #1 ====
luaOutputPins 2
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:luaOutputPins3 -->
==== output #2 ====
luaOutputPins 3
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:luaOutputPins4 -->
==== output #3 ====
luaOutputPins 4
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:luaOutputPins5 -->
==== output #4 ====
luaOutputPins 5
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:luaOutputPins6 -->
==== output #5 ====
luaOutputPins 6
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:luaOutputPins7 -->
==== output #6 ====
luaOutputPins 7
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:luaOutputPins8 -->
==== output #7 ====
luaOutputPins 8
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- section:luaCommands -->
== Lua Buttons ==

<!-- section:accelerometerDlg -->
= Accelerometer =

<!-- field:useSpiImu -->
==== Use SPI accelerometer ( false = CAN)  ====
If enabled - use onboard SPI Accelerometer, otherwise listen for CAN messages

<!-- section:mcp3208setup -->
= MCP3208 ADC devices =

<!-- field:mcp3208spidevice -->
==== SPI Device ====
* '''$spi_device_e_enum'''

<!-- field:mcp3208spidevice_1cs -->
==== SPI Chip Select1 ====
* '''$gpio_list'''

<!-- field:mcp3208spidevice_2cs -->
==== SPI Chip Select2 ====
* '''$gpio_list'''

<!-- field:mcp3208spidevice_3cs -->
==== SPI Chip Select3 ====
* '''$gpio_list'''

<!-- field:mcp3208divider -->
==== voltage divider ====
input voltage divider used in the mcp3208

<!-- field:mcp3208vref -->
==== vref ====
VREF used in the mcp3208

<!-- section:egtInputs -->
= EGT =

<!-- section:egtInputsCan -->
== CAN EGT sensors ==

<!-- field:enableAemXSeriesEgt -->
==== CAN EGT (AEM X series of RusEFI) ====
AEM X-Series EGT gauge kit or rusEFI EGT sensor from Wideband controller

<!-- field:ecumasterEgtToCan -->
==== Enable EcuMaster EGT to CAN ====
Read EcuMaster EGT to CAN. Expects little endian (Intel), and the CAN IDs specified below.

<!-- field:ecumasterEgtToCanBaseId -->
==== EcuMaster EGT to CAN base address ====
Default 1552 for EMU Classic, 1632 for EMU Black.

<!-- section:egtInputsSpi -->
== SPI EGT sensors ==

<!-- field:disablemax31855 -->
==== Disable Max 31855 ====
Disable onboard EGT31855

<!-- field:max31855spiDevice -->
==== MAX31855/MAX31856 SPI ====
* '''$spi_device_e_enum'''

<!-- field:max31855_cs1 -->
==== CS for EGT1 ====
max31855_cs 1

* '''$gpio_list'''

<!-- field:max31855_cs2 -->
==== CS for EGT2 ====
max31855_cs 2

* '''$gpio_list'''

<!-- field:max31855_cs3 -->
==== CS for EGT3 ====
max31855_cs 3

* '''$gpio_list'''

<!-- field:max31855_cs4 -->
==== CS for EGT4 ====
max31855_cs 4

* '''$gpio_list'''

<!-- field:max31855_cs5 -->
==== CS for EGT5 ====
max31855_cs 5

* '''$gpio_list'''

<!-- field:max31855_cs6 -->
==== CS for EGT6 ====
max31855_cs 6

* '''$gpio_list'''

<!-- field:max31855_cs7 -->
==== CS for EGT7 ====
max31855_cs 7

* '''$gpio_list'''

<!-- field:max31855_cs8 -->
==== CS for EGT8 ====
max31855_cs 8

* '''$gpio_list'''

<!-- group:Expert -->
= Expert =

<!-- section:spiBuses -->
== SPI Buses ==

<!-- section:spiBus1 -->
=== SPI1 settings ===

<!-- field:is_enabled_spi_1 -->
==== SPI1 Enable ====

<!-- field:spi1mosiPin -->
==== MOSI ====
* '''$gpio_list'''

<!-- field:spi1MosiMode -->
==== MOSI mode ====
Modes count be used for 3v<>5v integration using pull-ups/pull-downs etc.

* '''$pin_mode_e_enum'''

<!-- field:spi1misoPin -->
==== MISO ====
* '''$gpio_list'''

<!-- field:spi1MisoMode -->
==== MISO mode ====
* '''$pin_mode_e_enum'''

<!-- field:spi1sckPin -->
==== SCK ====
* '''$gpio_list'''

<!-- field:spi1SckMode -->
==== SCK mode ====
* '''$pin_mode_e_enum'''

<!-- section:spiBus2 -->
=== SPI2 settings ===

<!-- field:is_enabled_spi_2 -->
==== SPI2 Enable ====

<!-- field:spi2mosiPin -->
==== MOSI ====
* '''$gpio_list'''

<!-- field:spi2MosiMode -->
==== MOSI mode ====
* '''$pin_mode_e_enum'''

<!-- field:spi2misoPin -->
==== MISO ====
* '''$gpio_list'''

<!-- field:spi2MisoMode -->
==== MISO mode ====
* '''$pin_mode_e_enum'''

<!-- field:spi2sckPin -->
==== SCK ====
* '''$gpio_list'''

<!-- field:spi2SckMode -->
==== SCK mode ====
* '''$pin_mode_e_enum'''

<!-- section:spiBus3 -->
=== SPI3 settings ===

<!-- field:is_enabled_spi_3 -->
==== SPI3 Enable ====

<!-- field:spi3mosiPin -->
==== MOSI ====
* '''$gpio_list'''

<!-- field:spi3MosiMode -->
==== MOSI mode ====
* '''$pin_mode_e_enum'''

<!-- field:spi3misoPin -->
==== MISO ====
* '''$gpio_list'''

<!-- field:spi3MisoMode -->
==== MISO mode ====
* '''$pin_mode_e_enum'''

<!-- field:spi3sckPin -->
==== SCK ====
* '''$gpio_list'''

<!-- field:spi3SckMode -->
==== SCK mode ====
* '''$pin_mode_e_enum'''

<!-- section:spiBus4 -->
=== SPI4 settings ===

<!-- field:is_enabled_spi_4 -->
==== SPI4 Enable ====

<!-- section:spiBus5 -->
=== SPI5 settings ===

<!-- field:is_enabled_spi_5 -->
==== SPI5 Enable ====

<!-- section:spiBus6 -->
=== SPI6 settings ===

<!-- field:is_enabled_spi_6 -->
==== SPI6 Enable ====

<!-- section:spiDevices -->
== SPI Devices ==

<!-- field:useSpiImu#1 -->
==== Use SPI accelerometer ====
If enabled - use onboard SPI Accelerometer, otherwise listen for CAN messages

<!-- section:monitoringSettings -->
== rusEFI console ==

<!-- field:engineSnifferRpmThreshold -->
==== Engine Sniffer Threshold ====
Engine sniffer would be disabled above this rpm
set engineSnifferRpmThreshold X

<!-- section:allPins1 -->
== Full pinout 1/3 ==

<!-- field:triggerSimulatorPins1 -->
==== trigger stimulator output #1 ====
Each rusEFI piece can provide synthetic trigger signal for external ECU. Sometimes these wires are routed back into trigger inputs of the same rusEFI board.
See also directSelfStimulation which is different. 1

* '''$gpio_list'''

<!-- field:triggerSimulatorPins2 -->
==== trigger stimulator output #2 ====
Each rusEFI piece can provide synthetic trigger signal for external ECU. Sometimes these wires are routed back into trigger inputs of the same rusEFI board.
See also directSelfStimulation which is different. 2

* '''$gpio_list'''

<!-- field:camSimulatorPin -->
==== camSimulatorPin ====
* '''$gpio_list'''

<!-- field:tle6240_cs -->
==== tle6240_cs ====
* '''$gpio_list'''

<!-- field:tle6240spiDevice -->
==== tle6240 SPI ====
* '''$spi_device_e_enum'''

<!-- field:tachOutputPin -->
==== Tachometer output ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:o2heaterPin -->
==== Narrowband O2 heater output ====
On-off O2 sensor heater control. 'ON' if engine is running, 'OFF' if stopped or cranking.
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:idle_solenoidPin -->
==== Idle Solenoid Primary output ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:secondSolenoidPin -->
==== Idle Solenoid Secondary output ====
Some Subaru and some Mazda use double-solenoid idle air valve
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:idle_stepperDirectionPin -->
==== Idle Stepper Dir ====
* '''$gpio_list'''

<!-- field:idle_stepperStepPin -->
==== Idle Stepper Step ====
* '''$gpio_list'''

<!-- field:stepperEnablePin -->
==== Idle Stepper Enable ====
* '''$gpio_list'''

<!-- field:fuelPumpPin -->
==== Fuel Pump output ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:malfunctionIndicatorPin -->
==== MIL/Check Engine output ====
Check engine light, also malfunction indicator light. Always blinks once on boot.
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:fanPin -->
==== Fan Pin ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:acRelayPin -->
==== A/C Relay ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:mainRelayPin -->
==== Main Relay Pin ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:starterRelayDisablePin -->
==== Starter Relay Pin ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:auxAnalogInputs1#1 -->
==== Aux ADC #1 ====
auxAnalogInputs 1
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs2#1 -->
==== Aux ADC #2 ====
auxAnalogInputs 2
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs3#1 -->
==== Aux ADC #3 ====
auxAnalogInputs 3
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs4#1 -->
==== Aux ADC #4 ====
auxAnalogInputs 4
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs5#1 -->
==== Aux ADC #5 ====
auxAnalogInputs 5
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs6#1 -->
==== Aux ADC #6 ====
auxAnalogInputs 6
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs7#1 -->
==== Aux ADC #7 ====
auxAnalogInputs 7
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxAnalogInputs8#1 -->
==== Aux ADC #8 ====
auxAnalogInputs 8
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:spi1mosiPin#1 -->
==== SPI1 MOSI ====
* '''$gpio_list'''

<!-- field:spi1misoPin#1 -->
==== SPI1 MISO ====
* '''$gpio_list'''

<!-- field:spi1sckPin#1 -->
==== SPI1 SCK ====
* '''$gpio_list'''

<!-- field:spi2mosiPin#1 -->
==== SPI2 MOSI ====
* '''$gpio_list'''

<!-- field:spi2misoPin#1 -->
==== SPI2 MISO ====
* '''$gpio_list'''

<!-- field:spi2sckPin#1 -->
==== SPI2 SCK ====
* '''$gpio_list'''

<!-- field:spi3mosiPin#1 -->
==== SPI3 MOSI ====
* '''$gpio_list'''

<!-- field:spi3misoPin#1 -->
==== SPI3 MISO ====
* '''$gpio_list'''

<!-- field:spi3sckPin#1 -->
==== SPI3 SCK ====
* '''$gpio_list'''

<!-- field:spi4mosiPin -->
==== SPI4 MOSI ====
* '''$gpio_list'''

<!-- field:spi4misoPin -->
==== SPI4 MISO ====
* '''$gpio_list'''

<!-- field:spi4sckPin -->
==== SPI4 SCK ====
* '''$gpio_list'''

<!-- field:spi5mosiPin -->
==== SPI5 MOSI ====
* '''$gpio_list'''

<!-- field:spi5misoPin -->
==== SPI5 MISO ====
* '''$gpio_list'''

<!-- field:spi5sckPin -->
==== SPI5 SCK ====
* '''$gpio_list'''

<!-- field:spi6mosiPin -->
==== SPI6 MOSI ====
* '''$gpio_list'''

<!-- field:spi6misoPin -->
==== SPI6 MISO ====
* '''$gpio_list'''

<!-- field:spi6sckPin -->
==== SPI6 SCK ====
* '''$gpio_list'''

<!-- field:cdmInputPin -->
==== Saab CDM knock ====
Saab Combustion Detection Module knock signal input pin
also known as Saab Ion Sensing Module

* '''$gpio_list'''

<!-- field:drv8860_cs -->
==== DRV8860 CS ====
* '''$gpio_list'''

<!-- field:drv8860_csPinMode -->
==== DRV8860 CS Mode ====
* '''$pin_output_mode_e_enum'''

<!-- field:drv8860_miso -->
==== DRV8860 MISO pin ====
* '''$gpio_list'''

<!-- field:drv8860spiDevice -->
==== DRV8860 SPI ====
* '''$spi_device_e_enum'''

<!-- section:allPins2 -->
== Full pinout 2/3 ==

<!-- field:injectionPins1 -->
==== Injection Output 1 ====
injectionPins 1
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:injectionPins2 -->
==== Injection Output 2 ====
injectionPins 2
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:injectionPins3 -->
==== Injection Output 3 ====
injectionPins 3
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:injectionPins4 -->
==== Injection Output 4 ====
injectionPins 4
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:injectionPins5 -->
==== Injection Output 5  ====
injectionPins 5
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:injectionPins6 -->
==== Injection Output 6  ====
injectionPins 6
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:injectionPins7 -->
==== Injection Output 7  ====
injectionPins 7
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:injectionPins8 -->
==== Injection Output 8  ====
injectionPins 8
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:auxSpeedSensorInputPin1 -->
==== auxSpeedSensorInputPin1 ====
auxSpeedSensorInputPin 1
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:auxSpeedSensorInputPin2 -->
==== auxSpeedSensorInputPin2 ====
auxSpeedSensorInputPin 2
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:auxSpeedSensorInputPin3 -->
==== auxSpeedSensorInputPin3 ====
auxSpeedSensorInputPin 3
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:auxSpeedSensorInputPin4 -->
==== auxSpeedSensorInputPin4 ====
auxSpeedSensorInputPin 4
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:ignitionPins1 -->
==== Ignition Output 1 ====
ignitionPins 1
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:ignitionPins2 -->
==== Ignition Output 2 ====
ignitionPins 2
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:ignitionPins3 -->
==== Ignition Output 3 ====
ignitionPins 3
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:ignitionPins4 -->
==== Ignition Output 4 ====
ignitionPins 4
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:ignitionPins5 -->
==== Ignition Output 5 ====
ignitionPins 5
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:ignitionPins6 -->
==== Ignition Output 6 ====
ignitionPins 6
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:ignitionPins7 -->
==== Ignition Output 7 ====
ignitionPins 7
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:ignitionPins8 -->
==== Ignition Output 8 ====
ignitionPins 8
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:debugTriggerSync -->
==== Debug Trigger Sync ====
* '''$gpio_list'''

<!-- section:allPinsMC33 -->
=== MC33816 ===

<!-- field:mc33816_cs -->
==== Chip Select ====
* '''$gpio_list'''

<!-- field:mc33816_rstb -->
==== rstb ====
ResetB

* '''$gpio_list'''

<!-- field:mc33816_flag0 -->
==== flag0 ====
* '''$gpio_list'''

<!-- field:mc33816_driven -->
==== mc33816_driven ====
* '''$gpio_list'''

<!-- field:mc33816spiDevice -->
==== mc33816spiDevice ====
* '''$spi_device_e_enum'''

<!-- field:hpfpValvePin -->
==== hpfpValvePin ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- section:allPins3_1_and_2 -->
== Full pinout 3/3 ==

<!-- section:allPinsSensors -->
=== Sensors ===

<!-- field:throttlePedalPositionAdcChannel -->
==== Throttle pedal Position Channel ====
Electronic throttle pedal position first channel
See throttlePedalPositionSecondAdcChannel for second channel
See also tps1_1AdcChannel
See throttlePedalUpVoltage and throttlePedalWOTVoltage
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:throttlePedalPositionSecondAdcChannel -->
==== Throttle pedal Position #2 ====
Electronic throttle pedal position input
Second channel
See also tps1_1AdcChannel
See throttlePedalSecondaryUpVoltage and throttlePedalSecondaryWOTVoltage
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:triggerInputPins1 -->
==== Primary input channel ====
triggerInputPins 1
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:triggerInputPins2 -->
==== Secondary channel ====
triggerInputPins 2
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:camInputs1 -->
==== Cam Sync/VVT input ====
Camshaft input could be used either just for engine phase detection if your trigger shape does not include cam sensor as 'primary' channel, or it could be used for Variable Valve timing on one of the camshafts. 1
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:clt_adcChannel -->
==== CLT ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:iat_adcChannel -->
==== IAT ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:vbattAdcChannel -->
==== vBatt ADC input ====
This is the processor input pin that the battery voltage circuit is connected to, if you are unsure of what pin to use, check the schematic that corresponds to your PCB.
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:tps1_1AdcChannel -->
==== TPS1 ADC input ====
First throttle body, first sensor. See also pedalPositionAdcChannel
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:tps2_1AdcChannel -->
==== TPS2 ADC input ====
Second throttle body position sensor, single channel so far
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:mafAdcChannel -->
==== MAF ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:maf2AdcChannel -->
==== MAF 2 ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:frequencyMafChannel -->
==== Frequency MAF ====
Frequency MAF channel
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:afr_hwChannel -->
==== AFR ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:afr_hwChannel2 -->
==== AFR 2 ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:baroSensor_hwChannel -->
==== Baro ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:map_sensor_hwChannel -->
==== MAP ADC input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:fuelLevelSensor -->
==== Fuel Level input ====
This is the processor pin that your fuel level sensor in connected to. This is a non standard input so will need to be user defined.
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:vehicleSpeedSensorInputPin -->
==== Vehicle Speed input ====
?highlight=class~event_inputs

* '''$brain_input_pin_e_list'''

<!-- field:clutchDownPin -->
==== Clutch Down input ====
Some cars have a switch to indicate that clutch pedal is all the way down
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:clutchUpPin -->
==== Clutch Up input ====
Some vehicles have a switch to indicate that clutch pedal is all the way up
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:brakePedalPin -->
==== Brake pedal input ====
Brake pedal switch
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:acSwitch -->
==== A/C Switch ====
A/C button input
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:transmissionIdleUpPin -->
==== Transmission idle up switch ====
Transmission idle up switch input
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- field:auxTempSensor1_adcChannel -->
==== Aux Temperature #1 ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxTempSensor2_adcChannel -->
==== Aux Temperature #2 ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:auxFastSensor1_adcChannel -->
==== Aux Fast Analog ====
Useful in Research&Development phase
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:vvtPins1 -->
==== VVT solenoid bank 1 intake ====
VVT output solenoid pin for this cam 1
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:vvtPins2 -->
==== VVT solenoid bank 1 exhaust ====
VVT output solenoid pin for this cam 2
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:vvtPins3 -->
==== VVT solenoid bank 2 intake ====
VVT output solenoid pin for this cam 3
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:vvtPins4 -->
==== VVT solenoid bank 2 exhaust ====
VVT output solenoid pin for this cam 4
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:auxValves1 -->
==== Aux Valve #1 ====
auxValves 1

* '''$gpio_list'''

<!-- field:auxValves2 -->
==== Aux Valve #2 ====
auxValves 2

* '''$gpio_list'''

<!-- field:tle8888_cs -->
==== TLE8888 Chip Select ====
* '''$gpio_list'''

<!-- field:tle8888spiDevice -->
==== TLE 8888 spi ====
* '''$spi_device_e_enum'''

<!-- field:l9779_cs -->
==== L9779 Chip Select ====
* '''$gpio_list'''

<!-- field:startStopButtonPin -->
==== Start/Stop Button ====
See also starterControlPin
?highlight=class~switch_inputs

* '''$switch_input_pin_e_list'''

<!-- section:crankingTpsCurve -->
== Cranking Fuel TPS Multiplier ==

<!-- section:dcMotorActuatorHw -->
== ETB / DC motor actuator(s) hardware ==

<!-- section:dcHbridgeHardware -->
=== H-Bridge Hardware ===

<!-- field:etb_use_two_wires -->
==== Two-wire mode ====
TLE7209 and L6205 use two-wire mode. TLE9201 and VNH2SP30 do NOT use two wire mode.

<!-- section:connection -->
== Secondary Serial ==

<!-- section:tsPort -->
=== Calibration Secondary Serial ===

<!-- field:tunerStudioSerialSpeed -->
==== tunerStudioSerialSpeed ====
Secondary TTL channel baud rate

<!-- field:binarySerialTxPin -->
==== TX pin ====
See also EFI_CONSOLE_RX_BRAIN_PIN

* '''$gpio_list'''

<!-- field:binarySerialRxPin -->
==== RX pin ====
* '''$gpio_list'''

<!-- field:uartConsoleSerialSpeed -->
==== uartConsoleSerialSpeed ====
Band rate for primary TTL

<!-- field:enableKline -->
==== enableKline ====

<!-- section:baroSettings -->
== Barometer sensor ==

<!-- section:baroSettingsContent -->
=== Barometer sensor ===

<!-- field:useFixedBaroCorrFromMap -->
==== Grab baro value from MAP ====
Read MAP sensor on ECU start-up to use as baro value.

<!-- section:analogBaroSettings -->
==== Analog Sensor ====

<!-- field:baroSensor_hwChannel#1 -->
==== Baro input ====
?highlight=class~analog_inputs

* '''$adc_channel_e_list'''

<!-- field:baroSensor_type -->
==== Type ====

<!-- field:baroSensor_lowValue -->
==== BARO value low point ====
kPa value at low volts

<!-- field:baroLowValueVoltage -->
==== BARO voltage low point ====
BARO voltage for low point

<!-- field:baroSensor_highValue -->
==== BARO value high point ====
kPa value at high volts

<!-- field:baroHighValueVoltage -->
==== BARO voltage high value ====
BARO voltage for low point

<!-- section:digitalBaroSettings -->
==== Digital Sensor ====

<!-- field:lps25BaroSensorScl -->
==== LPS2x Baro SCL ====
* '''$gpio_list'''

<!-- field:lps25BaroSensorSda -->
==== LPS2x Baro SDA ====
* '''$gpio_list'''

<!-- section:hondaKDialog -->
== Honda K ==

<!-- field:hondaKcltGaugeAdder -->
==== CLT Gauge Adder ====

<!-- field:use_honda_k_ac -->
==== Use Honda K for AC switch ====

<!-- field:klineAcDebounceTime -->
==== K line AC debounce time ====
seconds to debounce kline ac

<!-- field:kLineDoHondaSend -->
==== K-Line Do Honda Send ====

<!-- field:kLineBaudRate -->
==== K-Line Baud Rate ====

<!-- field:kLinePeriodUs -->
==== K-Line Period Us ====

<!-- field:verboseKLine -->
==== K-Line Verbose ====

<!-- field:hondaK -->
==== K-Line Honda ====

<!-- field:hondaK_blipSends -->
==== Send different kvalue[0] / kvalue[1] every X sends ====

<!-- field:hondaK_batLightOn -->
==== K-Line battery light on kvalue[2] ====

<!-- field:hondaK_batLightOff -->
==== K-Line battery light off kvalue[2] ====

<!-- field:hondaK_battery_threshold -->
==== K-Line battery light on below V, engine off ====

<!-- field:hondaK_battery_thresholdEngineOn -->
==== K-Line battery light on below V, engine on ====

<!-- field:hondaK_battery_hysteresis -->
==== K-Line battery V hysteresis ====

<!-- field:batteryAverageExp -->
==== K-Line battery V average exp ====
A higher alpha (closer to 1) means the EMA reacts more quickly to changes in the data.
'1' means no filtering, 0.98 would be some filtering.

<!-- field:hondaK_kvalues0 -->
==== K-Line kvalues[0] ====

<!-- field:hondaK_kvalues1 -->
==== K-Line kvalues[1] ====

<!-- field:hondaK_kvalues2 -->
==== K-Line kvalues[2] battery light ====

<!-- field:hondaK_kvalues3 -->
==== K-Line kvalues[3] clt  ====

<!-- field:hondaK_kvalues4 -->
==== K-Line kvalues[4] ====

<!-- field:hondaK_kvalues5 -->
==== K-Line kvalues[5] ====

<!-- field:hondaK_kvalues6 -->
==== K-Line kvalues[6] ====

<!-- field:hondaK_kvalues7 -->
==== K-Line kvalues[7] ====

<!-- section:hondaCanDialog -->
== Honda CAN ==

<!-- field:hondaCanGen -->
==== Honda CAN Generation ====
Honda CAN generation - changes RPM message size

* '''1st Gen (7 bytes)'''
* '''2nd Gen (4 bytes)'''
* '''3rd Gen (8 bytes)'''

<!-- field:hondaCanSpeedUnit -->
==== Speed Unit ====
Honda CAN speed multiplier - KMH uses 100x, MPH uses 160x

* '''KMH (100x)'''
* '''MPH (160x)'''

<!-- section:parkingLot -->
== Experimental 1 ==

<!-- field:uiMode -->
==== uiMode ====
* '''Full'''
* '''Tuning'''

<!-- field:can1ListenMode -->
==== can1ListenMode ====
ListenMode is about acknowledging CAN traffic on the protocol level. Different from canWriteEnabled

<!-- field:can2ListenMode -->
==== can2ListenMode ====

<!-- field:rethrowHardFault -->
==== rethrowHardFault ====

<!-- field:canGpioType -->
==== canGpioType ====
* '''None'''
* '''DRT protocol'''
* '''MS protocol'''

<!-- field:yesUnderstandLocking -->
==== I understand ECU Locking ====
* '''no'''
* '''yes'''

<!-- field:tuneHidingKey -->
==== Tune read/write password ====

<!-- field:verboseQuad -->
==== verboseQuad ====

<!-- field:vvtBooleanForVerySpecialCases -->
==== vvtBooleanForVerySpecialCases ====

<!-- field:watchOutForLinearTime -->
==== watchOutForLinearTime ====

<!-- field:verboseIsoTp -->
==== TS over CAN debug ====
Are you a developer troubleshooting TS over CAN ISO/TP?

<!-- field:triggerEventsTimeoutMs -->
==== Engine Movement Recently Timeout ====

<!-- field:injectionPinMode -->
==== injection Output(s) Mode ====
* '''$pin_output_mode_e_enum'''

<!-- field:ignitionPinMode -->
==== Ignition Output Mode ====
* '''$pin_output_mode_e_enum'''

<!-- field:consumeObdSensors -->
==== consumeObdSensors ====
This property is useful if using rusEFI as TCM or BCM only

<!-- field:allowIdenticalPps -->
==== Allow Identical PPS - no redundancy for ETB ====

<!-- field:ignore_tps_pps_sensors_too_close -->
==== Ignore TPS/PPS sensors too close  (BRZ/FRS/GT86) ====
Ignore TPS/PPS sensors too close to each other

<!-- field:alwaysInstantRpm -->
==== Always use instant RPM ====
RPM is measured based on last 720 degrees while instant RPM is measured based on the last 90 degrees of crank revolution

<!-- field:modeledFlowIdle -->
==== Modeled flow idle ====

<!-- field:idleMaximumAirmass -->
==== Max idle flow ====
Maximum commanded airmass for the idle controller.

<!-- field:turbochargerFilter -->
==== turbochargerFilter ====

<!-- field:auxFrequencyFilter -->
==== auxFrequencyFilter ====

<!-- field:useBiQuadOnAuxSpeedSensors -->
==== useBiQuadOnAuxSpeedSensors ====

<!-- field:kickStartCranking -->
==== TODO KS mode 4569 ====

<!-- field:useAdvanceCorrectionsForCranking -->
==== Use Advance Ignition Corrections for cranking ====
This enables the various ignition corrections during cranking (IAT, CLT and PID idle).
You probably don't need this.

<!-- section:parkingLot2 -->
== Experimental 2 ==

<!-- field:dacOutputPins1 -->
==== dacOutputPins1 ====
dacOutputPins 1

* '''$gpio_list'''

<!-- field:dacOutputPins2 -->
==== dacOutputPins2 ====
dacOutputPins 2

* '''$gpio_list'''

<!-- field:luaCanRxWorkaround -->
==== luaCanRxWorkaround CAN performance hack ====
global_can_data performance hack

<!-- field:canInputBCM -->
==== Read RPM matching VSS profile ====

<!-- field:auxSpeed1Multiplier -->
==== auxSpeed1Multiplier ====

<!-- field:brakeMeanEffectivePressureDifferential -->
==== brakeMeanEffectivePressureDifferential ====

<!-- section:trigger_advanced -->
== Advanced Trigger ==

<!-- field:camSyncOnSecondCrankRevolution -->
==== Cam sync crank revolution ====
Does the cam sensor signal indicate a sync on the second or first engine phase?

* '''first'''
* '''second'''

<!-- field:mapCamDetectionAnglePosition -->
==== MAP readout angle ====
Magic engine phase: we compare instant MAP at X to instant MAP at x+360 angle in one complete cycle

<!-- field:mapSyncThreshold -->
==== MAP delta threshold ====
Delta kPa for MAP sync

<!-- field:useNoiselessTriggerDecoder -->
==== Enable noise filtering ====

<!-- section:trigger_console -->
=== Console Logging ===

<!-- field:verboseVVTDecoding -->
==== Print verbose VVT sync details to console ====
Verbose info in console below engineSnifferRpmThreshold

<!-- field:verboseTriggerSynchDetails -->
==== Print verbose trigger sync to console ====
Verbose info in console below engineSnifferRpmThreshold

<!-- field:displayLogicLevelsInEngineSniffer -->
==== Display logic signals ====
Shall we display real life signal or just the part consumed by trigger decoder.
Applies to both trigger and cam/vvt input.

<!-- field:silentTriggerError -->
==== Do not print messages in case of sync error ====
Sometimes we have a performance issue while printing error

<!-- field:engineSnifferFocusOnInputs -->
==== Focus on inputs in engine sniffer ====
In this mode only trigger events go into engine sniffer and not coils/injectors etc

<!-- section:triggerConfiguration_gap -->
== Trigger Gap Override ==

<!-- field:overrideTriggerGaps -->
==== Override well known trigger gaps ====

<!-- field:gapTrackingLengthOverride -->
==== gapTrackingLengthOverride ====
How many consecutive gap rations have to match expected ranges for sync to happen

<!-- field:triggerGapOverrideFrom1 -->
==== First gap from ====
triggerGapOverrideFrom 1

<!-- field:triggerGapOverrideTo1 -->
==== First gap to ====
triggerGapOverrideTo 1

<!-- field:triggerGapOverrideFrom2 -->
==== Second gap from ====
triggerGapOverrideFrom 2

<!-- field:triggerGapOverrideTo2 -->
==== Second gap to ====
triggerGapOverrideTo 2

<!-- field:triggerGapOverrideFrom3 -->
==== Gap #3 from ====
triggerGapOverrideFrom 3

<!-- field:triggerGapOverrideTo3 -->
==== Gap #3 to ====
triggerGapOverrideTo 3

<!-- field:triggerGapOverrideFrom4 -->
==== Gap #4 from ====
triggerGapOverrideFrom 4

<!-- field:triggerGapOverrideTo4 -->
==== Gap #4 to ====
triggerGapOverrideTo 4

<!-- field:triggerGapOverrideFrom5 -->
==== Gap #5 from ====
triggerGapOverrideFrom 5

<!-- field:triggerGapOverrideTo5 -->
==== Gap #5 to ====
triggerGapOverrideTo 5

<!-- field:triggerGapOverrideFrom6 -->
==== Gap #6 from ====
triggerGapOverrideFrom 6

<!-- field:triggerGapOverrideTo6 -->
==== Gap #6 to ====
triggerGapOverrideTo 6

<!-- field:triggerGapOverrideFrom7 -->
==== Gap #7 from ====
triggerGapOverrideFrom 7

<!-- field:triggerGapOverrideTo7 -->
==== Gap #7 to ====
triggerGapOverrideTo 7

<!-- field:triggerGapOverrideFrom8 -->
==== Gap #8 from ====
triggerGapOverrideFrom 8

<!-- field:triggerGapOverrideTo8 -->
==== Gap #8 to ====
triggerGapOverrideTo 8

<!-- field:overrideVvtTriggerGaps -->
==== Override well known VVT gaps ====

<!-- field:gapVvtTrackingLengthOverride -->
==== gapVvtTrackingLengthOverride ====
How many consecutive VVT gap rations have to match expected ranges for sync to happen

<!-- field:triggerVVTGapOverrideFrom1 -->
==== First VVT gap from ====
triggerVVTGapOverrideFrom 1

<!-- field:triggerVVTGapOverrideTo1 -->
==== First VVT gap to ====
triggerVVTGapOverrideTo 1

<!-- field:triggerVVTGapOverrideFrom2 -->
==== Second VVT gap from ====
triggerVVTGapOverrideFrom 2

<!-- field:triggerVVTGapOverrideTo2 -->
==== Second VVT gap to ====
triggerVVTGapOverrideTo 2

<!-- field:triggerVVTGapOverrideFrom3 -->
==== VVT gap #3 from ====
triggerVVTGapOverrideFrom 3

<!-- field:triggerVVTGapOverrideTo3 -->
==== VVT gap #3 to ====
triggerVVTGapOverrideTo 3

<!-- field:triggerVVTGapOverrideFrom4 -->
==== VVT gap #4 from ====
triggerVVTGapOverrideFrom 4

<!-- field:triggerVVTGapOverrideTo4 -->
==== VVT gap #4 to ====
triggerVVTGapOverrideTo 4

<!-- section:harleyAcr -->
== Harley ==

<!-- field:acrPin -->
==== Pin ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:acrPin2 -->
==== Pin 2 ====
?highlight=class~outputs

* '''$output_pin_e_list'''

<!-- field:acrRevolutions -->
==== Disable after revolutions ====

<!-- field:acrDisablePhase -->
==== Disable after engine phase ====
During revolution where ACR should be disabled at what specific angle to disengage

<!-- field:harleyAcrSprayFuel -->
==== Spray Fuel during ACR ====
Spray fuel with ACR active

<!-- section:idleFlowEstimate -->
== Idle flow estimate ==

<!-- section:idleAirmassTimingEquivalence -->
== Idle airmass/timing equivalence ==

<!-- section:throttleEffectiveArea -->
== Throttle effective area ==

<!-- section:torque2TableTbl -->
== TMF ==