epicEFI Wiki - Recent changes [en]

Lua

Joesphan — Tue, 18 Aug 2026 04:08:53 GMT

Joesphan — Tue, 18 Aug 2026 02:49:32 GMT

Created page with "safsefwefewfewfwef"

New page

safsefwefewfewfwef

Joesphan — Tue, 18 Aug 2026 02:49:24 GMT

← Older revision		Revision as of 02:49, 18 August 2026
(One intermediate revision by the same user not shown)
Line 28:		Line 28:
	* '''[[Hardware]]''' — supported epicEFI hardware		* '''[[Hardware]]''' — supported epicEFI hardware
	* '''[[Triggers]]''' — check trigger pattern support		* '''[[Triggers]]''' — check trigger pattern support

			== Advanced ==
			* [[Lua]] — scripting documentation

	== Project ==		== Project ==
	* '''[[~~About\|~~About]]''' — what epicEFI is and how it works		* '''[[About]]''' — what epicEFI is and how it works
	* '''[[Contributing]]''' — how to help improve the project		* '''[[Contributing]]''' — how to help improve the project

Agnese — Fri, 07 Aug 2026 14:54:13 GMT

Stepper acceleration profile

@@ Line 361: / Line 361: @@
 Number of extra steps to overstep toward closed when re-parking after force-close. Compensates for stepper drift without needing the full startup homing sequence. 5 is a good starting point.
-<!-- section:IdleTimingTargetErrorDialog -->
+<!-- section:IdleTimingTargetErrorDialog -->= Stepper acceleration profile =
 = Open loop ignition idle timing (RPM-error) =
 Open-loop idle timing curve: ignition advance/retard as a function of how far RPM is from the idle target. Enabled by [[Idle#Open loop idle timing (RPM-error)|Open loop idle timing (RPM-error)]].

Agnese — Fri, 07 Aug 2026 14:21:41 GMT

Added DFCO exit enrichment example table

← Older revision		Revision as of 14:21, 7 August 2026
Line 427:		Line 427:
	= DFCO MAP to RPM threshold =		= DFCO MAP to RPM threshold =
	DFCO will activate when operating below this curve. Used to allow a higher threshold at low RPM where less vaccuum is generated.		DFCO will activate when operating below this curve. Used to allow a higher threshold at low RPM where less vaccuum is generated.

			= DFCO Exit Enrichment (%) =
			Example table:
			[[File:DFCOExitEnrichment Example Table.png\|none\|thumb\|Use this just as an example. These values may or may not work well on your engine]]

	= Long Term Fuel Trim =		= Long Term Fuel Trim =
	This configures the Long Term Fuel Trim. This is used to trim fuel over long periods of time, such as injector aging or similar factors.		This configures the Long Term Fuel Trim. This is used to trim fuel over long periods of time, such as injector aging or similar factors.

Agnese — Fri, 07 Aug 2026 14:18:54 GMT

New page

This is just to give an idea of how the axis and values should be scaled

Agnese — Fri, 07 Aug 2026 13:54:43 GMT

Added DFCO exit enrichment explanation

@@ Line 362: / Line 362: @@
 ==== Inhibit closed loop fuel after cut ====
 Pause closed loop fueling after deceleration fuel cut occurs. Set this to a little longer than however long is required for normal fueling behavior to resume after fuel cut.
 ==== Ignition retard during cut ====
@@ Line 374: / Line 368: @@
 ==== After cut timing ramp-in time ====
 Smooths the transition back from fuel cut. After fuel is restored, ramp timing back in over the period specified.
 = DFCO MAP to RPM threshold =